Share Superior package of Combination wardrobe rack in commercial selling
As we all know, the packaging size of the product is the main factor that directly affects the transportation cost. According to the requirements of our e-commerce customers, I will share with you the packaging that has passed the drop box test after the optimized cross-border e-commerce hot combo wardrobe rack.
As following product picture(Item code: GR19545195B5E) And product brief introduction:
Product Name: Combination wardrobe rack
Size: L1890×W450×H1950mm;
Pole Dia: 19x1.0mmT;
Wire Gap: 40mm;
Finish: coffe color, black,carbon grey
Consist of:
3pcs shelves of 450x450mm and 4pcs shelves of 750x450mm and 8pcs connected posts and 1pcs hanger of 450mm and 3pcs hanger of 750mm and 2pcs support rails and 64pcs plastic clips and 8pcs leveling feet.
The packaging needs to pass the international standard high degree of box drop test, which is the most basic requirement for the packaging of each product for cross-border e-commerce customers. After continuous testing and improvement by our company, the following is the latest packaging method that has passed the box drop test after optimization for this product , Optimized packaging, this product is individually filled with a 40-foot high container, and the container space is fully utilized. It is 80 sets more than before optimization (the four corners of the thickened pearl cotton protector increases the packaging size of the entire product). The product meets the customer's ideal requirements in this way and increases the customer's sales profit:
1.Fold the paper card sleeve first, put the paper card sleeves on both ends of the upper tube of each 4 pillars that were individually contracted (with black letters UPPER X 4PCS printed on both sides), and fold the two ends of the middle tube of each 4 pillars that were individually contracted. Put on the paper card sleeves (with black letters MIDDLE X 4PCS printed on both sides), and put the paper card sleeves on both ends of the lower tube of each 4 pillars that are individually contracted (black letters LOWER X 4PCS on both sides), and put the separately contracted Three 35mm clothes rails are covered with paper card sleeves on both ends (black letters are printed on both sides of LONG CLOTHES HANGER ROD X 3PCS). One side of the paper card sleeve and the pillar needs to be fixed with a little sealing glue:
.png)
2. Put the first piece of 750x450 mesh with the frame facing upwards, and put two pillar upper tubes inside, then cover the second piece of 750x450 mesh, and then put the third piece of 750x450 mesh with the frame facing upwards. Two columns of pillar middle pipes are added inside, and the last piece of 750x450 mesh is covered;
.jpg)
3. Put three pieces of 450x450 mesh on top of the 750x450 mesh, and use a piece of five-layer paper to cushion the bottom end of the 450x450 mesh without a cone sleeve.
.jpg)
4.After the 7 meshes are stacked together, tie the meshes at the center of the four sides with a cable tie (a 500mm cable tie binds the 7 meshes together, of which two 300mm cable ties together with a piece of 750x450mm mesh below Tied together), use four black plastic corner pads under the four corners of the mesh;
.jpg)
5.Tie the welded 450 clothes rail and 2 single waves together with a cable tie, and put the clothes rail accessories, clip bag, anti-falling plastic parts and instructions into the blank inner box, and seal it in a straight line. , And then place this box in the vacant position above the filling mesh:
.png)
6.Two bundles of 4 down tubes (underneath) with paper card sleeves at both ends are placed next to one end of the mesh, and then three 750 clothes rails with paper card sleeves are stacked on top of the mesh. The corners (sideways) are cushioned with two black plastic corner protectors:
.jpg)
7. After entering the box, use a 72mm wide sealing glue I-shaped seal, so far the whole set of products has been packaged.
.png)
